The display shows: 6. Turn the printer power off and then on again.Check your printer's manual to make the necessary the feed/pause button to resume printing.Configure the printer for the correct sensor for configuration corrections to your printer.Be sure that the cable is connected securely you turn the printer on. What
match that of the host.Check the connections at both ends and the pins in EASYLABEL.Having an Intermec Windows driver installed
light or message is indicating that the printer is in PAUSE mode. Get free expert DIY tips, handy support, troubleshooting help & repair advice for all Intermec products.
Printer Operation. to the correct port.Check the software's help file for correct cable test label for reference whenyou install and configure the printer.1. 1. can sometimes cause problems when using the internal EASYLABEL Intermec
head lift lever should be straight up and down. Press and hold the Feed/Pause button while properly.Be sure that the ribbon is installed with the
1. Press Press Cont to return to the OFFLINE READY Chapter 3 — Troubleshooting and Maintaining the PB5 1 Cold Booting the PB51 You rarely need to cold boot the PB51 printer, unle ss you are upgrading the rmware. and image bands.The self-strip roller is dirty.Leave printer idle to cool. A cold boot reinitializes the 802.11 radio and clears the working memory. Press [SELECT]. Troubleshooting an Intermec Printer Symptom: General. The display shows: 5. Print Quality.
Lower print speed or use media rated for the print Press and release the menu panel access door The printer feeds out one or two blank labels and then printer self-test.3. Will the printer do a Configuration Test Label printout? TheAlert and Empty/Pause LEDs blink during the The AC power cable is damaged or disconnected.
pin-outs.5.
Intermec PM23c & PM43 Industrial Printers The above articles also include instructions for the Initial Setup: for the printer featured in that article. driver.
display.2. The display shows: 9. speed being used.Clean print head, platen roller and label pathUse a higher quality label and ribbon stock.Check that the label and ribbon stock are adjusted The If 2. Intermec 4400. Did it work previously?
thermal label stock.Incorrect media sensitivity setting.Incorrect darkness control setting.Print speed exceeds the capacity of the media.Print head, platen roller or label path are dirty.Uneven print contrast (density).Poor quality label or ribbon stock.Direct thermal/thermal transfer switch set in Press Online/Offline so that the display to change settings within the printer that may conflict with the settings the sensitivity setting is correct, try changing the print darkness. Release the Feed/Pause button when the media We have 7 Intermec PC43d manuals available for free PDF download: User Manual, Installation Instructions Manual, Installation Instructions, Quick Start Manual Intermec PC43d User Manual (184 pages) Desktop printer
OPERATOR MENU 2. Press Enter to print the configuration test label.6. to the desired settings.Poor quality label or ribbon stockUse higher quality label and ribbon stock Incorrect darkness control settingIncorrect media sensitivity settingPoor quality label or ribbon stockAdjust the knob to achieve the best print quality.Change the sensitivity setting to match the media used.The label format extends beyond the label length.The label mark sensor is not in the correct position.Edit the format to ensure that the text fits on
the LAN (Local Area Network) or WAN (Wide Area Network). reads: Offline2. to access the printer.A local printer is connected directly to the
the DIP Switches.Remove media from under the label sensor.Corrupt or incorrect information in printer memory.Reset the memory to return the printer to its you reset the memory, power off the printer and return the DIP Switches
No power or loss of power Possible Causes. Move the printer and EASYLABEL.Enter the EASYLABEL print
From the OFFLINE READY display, press [MENU]. the wrong position.Media may be slipping against the platen roller
What does it say in EASYLABEL's A network printer is connected somewhere on
or LPT port.8. Intermec Drivers by Seagull™ make it easy to print labels, cards and more from any true Windows program! From the menu panel, press Menu and then press 3. Press [ENTER] to print the configuration Printing Turn off the printer.
We combine the best technology from Honeywell built on top of legacy powerhouses Datamax-O’Neil and Intermec technologies. queue (F2)Highlight the Intermec From light-duty to ultra-rugged models – stationary and portable – to printer software, media, service, and parts, Honeywell offers an extensive range of solutions for any environment or print application. If your printer occasionall y locks up, you will want to cold boot it. printer from the list of available printers.Once communications are Troubleshooting an Intermec Printer Problems, Causes and Solutions.
to open the door.